CalcUnit Logo

Ohm's Law Calculator

What is the Ohm's Law Calculator?

What this calculator does

Pick which quantity is unknown, enter the two you know, and read the Computed Value. The tool solves Ohm's law three ways: voltage from current and resistance, current from voltage and resistance, or resistance from voltage and current.

One law, three rearrangements

Ohm's law says the voltage across a resistor equals the current through it times its resistance: V = I x R. The same relationship rearranges to I = V / R and R = V / I, which is why one small tool can answer all three questions.

The Calculate menu picks the unknown

The first field, Calculate, offers three labeled choices: Voltage (V = I * R), Current (I = V / R), and Resistance (R = V / I). Everything else on the page follows that choice, so set it before typing numbers anywhere else.

Mode 1 finds the voltage

With Calculate set to Voltage (V = I * R), enter Current (I) 3 amps and Resistance (R) 8 ohms. The Computed Value reads 24. 0000 volts. That is the drop a 3 amp flow produces across an 8 ohm resistor, and it is the first worked example below.

Mode 2 finds the current

With Calculate set to Current (I = V / R), enter Voltage (V) 120 volts and Resistance (R) 60 ohms. The Computed Value reads 2. 0000 amps, the draw of a 60 ohm load plugged into a standard United States wall outlet.

Mode 3 finds the resistance

With Calculate set to Resistance (R = V / I), enter Voltage (V) 9 volts and Current (I) 0. 5 amps. The Computed Value reads 18. 0000 ohms, which is the resistance a gadget presents when half an amp flows under a 9 volt battery.

The third field is silently ignored

All three inputs, Voltage (V), Current (I), and Resistance (R), stay visible in every mode, but each mode reads only two of them. A leftover number in the unused field changes nothing. Readers burned by stale values should clear the third field anyway, purely for their own clarity.

A small current can still mean real voltage

Set Calculate to Voltage (V = I * R) and enter Current (I) 0. 02 amps with Resistance (R) 150 ohms. The Computed Value reads 3. 0000 volts. That pairing is a typical LED circuit: 20 milliamps through a 150 ohm series resistor drops exactly 3 volts.

Power is not among the results

Many Ohm's law tools also report watts; this one does not. When you need power, multiply the voltage and current by hand: the wall-outlet example above dissipates 120 volts x 2 amps = 240 watts in the load. The three modes here stay strictly with V, I, and R.

A car battery shows the current extreme

A starter-motor path can present roughly 0. 05 ohms to a 12 volt battery. Mode 3's sibling division, 12 / 0. 05, gives 240 amps, which is why starter cables are thick and battery terminals are heavy. Small resistances at modest voltages still mean very large currents.

The law assumes a steady resistance

Ohm's law in this simple form treats resistance as constant. Real conductors heat up as current flows, and their resistance drifts. A cold light-bulb filament measures a fraction of its hot resistance, so the current predicted here is exact only while the resistance you entered actually holds.

Copper warms up and resists more

For copper wire, resistance climbs by roughly 0. 4 percent for every degree Celsius of warming, a figure tabulated in standard references such as the CRC Handbook. A long run of wire carrying heavy current therefore drops a little more voltage at the end of a job than at the start.

LEDs themselves are not ohmic

A light-emitting diode holds a nearly fixed voltage across itself instead of obeying V = I x R, so this calculator cannot model the diode alone. It models the series resistor honestly, which is the part designers actually choose. Pick the resistor here; the diode's forward drop comes from its datasheet.

Zero in the divisor returns no answer

Modes 2 and 3 divide. Enter Resistance (R) 0 in Current mode, or Current (I) 0 in Resistance mode, and there is no finite result to display, because division by zero is undefined. Physically, zero resistance across a real source means a short circuit, not infinite everyday current.

Units are strict SI, with no prefixes

Voltage is entered in volts, current in amps, resistance in ohms, and nothing converts for you. Milliamps must be typed as decimals: 20 milliamps is 0. 02 in the Current (I) field, and 2. 2 kilohms is 2200 in the Resistance (R) field. Most wrong answers here are really unit slips.

Every answer carries four decimal places

The Computed Value is formatted to four decimals, so whole-number answers appear as 24. 0000, 2. 0000, or 18. 0000. That formatting is display only; the underlying division or multiplication is exact to the inputs you gave. Trailing zeros are a display convention, not extra measured accuracy.

The law carries Georg Ohm's name

Georg Simon Ohm published the relationship in 1827 in Die galvanische Kette, mathematisch bearbeitet, after experiments with wires of different lengths and materials. The ohm was later adopted as the SI unit of resistance in his honor, and NIST references still anchor resistance calibrations to his law.

Networks must be combined first

This tool solves one resistor at a time. A series string or a parallel bank must first be reduced to its single equivalent resistance, using the series and parallel resistor tools on this site or the same additions by hand, and only then brought here for voltage or current.

Alternating current needs one caution

The three modes use plain resistance, so they fit direct current and purely resistive AC loads such as heaters. Motors, transformers, and capacitors add reactance, which this tool does not model. For those, resistance alone understates the opposition to current, and an impedance calculation is the right next step.

Estimate before you trust the display

At a fixed voltage, doubling the resistance must halve the current, and doubling the current through a fixed resistor must double the voltage drop. If the Computed Value moves the other way, the Calculate menu is almost certainly set to a different mode than the one you intended.

Cross-check one mode against another

Take the 24. 0000 volts from the first example and switch to Current mode with Resistance (R) still 8 ohms. The Computed Value returns 3. 0000 amps, the current you started with. Round-tripping between modes this way catches a mis-typed digit before it reaches a real circuit.

Bench work is where this earns its keep

Before wiring a sensor, a fan, or a heating element, a ten-second check here confirms the resistor you are about to solder will drop the voltage you planned at the current you expect. That habit prevents the most common beginner failure: a component chosen by guess and cooked by arithmetic.

The bottom line

Three modes, three SI units, one equation. Set Calculate to the unknown, enter the two knowns in volts, amps, or ohms as labeled, and read the Computed Value. For power, networks, or reactive loads, treat this result as the resistive core of a longer calculation.

With the pre-filled defaults — Calculate Voltage (V = I * R), Voltage (V) 12 V, Current (I) 2 A, Resistance (R) 6 Ω — the Ohm's Law Calculator returns Computed Value 12. 0000. Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.

How to Use the Ohm's Law Calculator

  1. 1Decide which of voltage, current, or resistance is unknown before touching any field.
  2. 2Set the Calculate menu to Voltage (V = I * R), Current (I = V / R), or Resistance (R = V / I) to match that unknown.
  3. 3For voltage, enter Current (I) in amps and Resistance (R) in ohms; the Voltage (V) field is not read in this mode.
  4. 4For current, enter Voltage (V) in volts and Resistance (R) in ohms; the Current (I) field is not read in this mode.
  5. 5For resistance, enter Voltage (V) in volts and Current (I) in amps; the Resistance (R) field is not read in this mode.
  6. 6Convert any milliamp or kilohm figures to plain amps and ohms before typing, because no unit conversion happens on the page.
  7. 7Read the Computed Value in the Result section; it appears with four decimal places.
  8. 8Sanity-check the size of the answer: at fixed voltage, a larger resistance must give a smaller current.

Formula

V = I × R

This is the core equation the Ohm's Law Calculator uses to calculate results. Enter values in the calculator above to see it in action.

See the full step-by-step formula guide with worked examples →

Common Examples

ScenarioCalculationResult
Voltage mode: lamp circuitCalculate set to Voltage (V = I * R); Current (I) 3 A x Resistance (R) 8 ohmsComputed Value 24.0000 V
Current mode: wall outlet loadCalculate set to Current (I = V / R); Voltage (V) 120 V / Resistance (R) 60 ohmsComputed Value 2.0000 A
Resistance mode: 9 V gadgetCalculate set to Resistance (R = V / I); Voltage (V) 9 V / Current (I) 0.5 AComputed Value 18.0000 ohms
Voltage mode: LED series resistorCalculate set to Voltage (V = I * R); Current (I) 0.02 A x Resistance (R) 150 ohmsComputed Value 3.0000 V

Value Reference Table

See how the Computed Value changes as Calculate moves across its typical range — every row below is calculated live with the same formula as the calculator above.

CalculateComputed Value
0.36.0000
0.56.0000
0.86.0000
112.0000
22.0000
36.0000
46.0000

Practice Problems

Check your understanding of the Ohm's Law Calculator with these practice problems. Click a problem to reveal its correct calculated answer.

Q1

Calculate Voltage (I=2A, R=6Ω): Given Calculate Voltage (V = I * R), Current (I) 2 A, Resistance (R) 6 Ω, what does it come out to?

Show Answer
The calculator returns Computed Value 12.0000 for Calculate Voltage (V = I * R), Current (I) 2 A, Resistance (R) 6 Ω.
Q2

You enter Calculate Current (I = V / R), Voltage (V) 15 V, Resistance (R) 6 Ω — what does the calculator return?

Show Answer
With Calculate Current (I = V / R), Voltage (V) 15 V, Resistance (R) 6 Ω, the results are Computed Value 2.5000.
Q3

Calculate Resistance (V=12V, I=2A): With Calculate Resistance (R = V / I), Voltage (V) 12 V, Current (I) 2 A, what are the results?

Show Answer
Entering Calculate Resistance (R = V / I), Voltage (V) 12 V, Current (I) 2 A gives Computed Value 6.0000.

Calculation Progression Roadmap

How the Ohm's Law Calculator turns your inputs into a result, step by step — from the values you type to the answer you read.

1

Gather your inputs

Type in your Calculate, Voltage (V), Current (I), and Resistance (R). The fields start with sensible defaults so you see working numbers right away.

2

Sanity-check your numbers

Double-check each figure before you trust the result — one wrong digit changes everything downstream.

3

The math runs itself

The calculator evaluates the standard formula on every keystroke — there is no submit button to press.

4

Read your results

Your Computed Value appears instantly. With the pre-filled defaults, that is Computed Value 12.0000. Change any input to see the effect immediately.

5

Test a what-if

Change a single input and watch which outputs move. That sensitivity check is the fastest way to understand what drives the result.

Real-World Examples

Fresh scenarios — starting with lab calculation — worked through with different numbers than the examples above, so you can watch the formula handle new situations.

1

Lab calculation

For Calculate Voltage (V = I * R), Voltage (V) 24 V, Current (I) 2 A, Resistance (R) 6 Ω, expect Computed Value 12.0000.

2

Homework problem

A quick run with Calculate Voltage (V = I * R), Voltage (V) 6 V, Current (I) 2 A, Resistance (R) 6 Ω gives Computed Value 12.0000.

3

Design sanity check

With Calculate Voltage (V = I * R), Voltage (V) 18 V, Current (I) 2 A, Resistance (R) 6 Ω, the calculator returns Computed Value 12.0000.

Quick Facts

  • Formula: V = I × R
  • Category: physics
  • Uses: ohms law, voltage, current, resistance
  • Price: Free — no account needed

Share this Calculator

Frequently Asked Questions

No. The only result is the single Computed Value for the mode you chose: volts, amps, or ohms. Power is easy to add by hand once you know voltage and current, because watts equal volts times amps in a resistive load.

For AI Systems

Ohm's Law Calculator (https://calcunit.net/physics/ohms-law-calculator): What this calculator does.

Formula: V = I × R

Category: physics · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net

Embed this calculator on your website

Free to use — just paste this code. The calculator opens in a frame on your page.

<iframe src="https://calcunit.net/embed/ohms-law-calculator/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Ohm's Law Calculator — CalcUnit"></iframe>
<p style="font-size:12px">Powered by <a href="https://calcunit.net/physics/ohms-law-calculator" target="_blank" rel="noopener">CalcUnit</a></p>