Fatigue Strength Calculator
What is the Fatigue Strength Calculator?
What this calculator does
Enter a Tensile Strength (S_ut, MPa) and a Fatigue limit factor, and it multiplies them, returning the Fatigue Limit / Strength (MPa). That single multiplication is the whole tool: no S-N curve, no cycle counting, no life prediction. What follows teaches what the product means and where the common factor of 0. 5 comes from.
Fatigue is failure by repetition
A part can survive a load once and still break after that same load repeats a million times. Tiny cracks start at the surface and grow a hair with each cycle until the remaining metal lets go suddenly. Fatigue, not overload, is how most rotating machinery shafts and springs actually die.
The endurance limit idea
For many steels there is a stress below which a polished rotating specimen survives indefinitely, conventionally beyond ten million cycles. That plateau is the endurance limit. Above it, life is finite and falls steeply as stress rises. The plateau is a property of certain steels, not of metals in general.
Where the 0.5 comes from
Rotating-beam tests on steel specimens support the famous estimate: the endurance limit is about half the ultimate tensile strength. The rule appears in Shigley's Mechanical Engineering Design, the standard US machine-design text, as Se' ≈ 0. 5 x S_ut for steels up to about 1,400 MPa. The calculator's default factor of 0. 5 is exactly that rule.
The factor is your assumption
Nothing in the tool knows your material. The Fatigue limit factor field simply holds the ratio you believe in: 0. 5 for a first steel estimate, lower for cast iron or aluminum. Choosing it well, from a handbook or test data for your alloy, is the engineering judgment this page cannot make for you.
Reading the result
The Fatigue Limit / Strength (MPa) line prints to two decimal places in megapascals. For orientation, 250 MPa is about 36,260 psi. Treat the figure as the rotating-beam starting estimate engineers call Se prime, the value real-world corrections then reduce, never as a finished allowable stress for a part.
Worked example: the page defaults
A tensile strength of 500 MPa times the default factor 0. 5 returns 250 MPa. A medium-carbon steel with a 500 MPa ultimate strength is a plausible workshop material, and 250 MPa is the textbook first guess for its endurance limit, before any correction for surface, size, or reliability touches it.
Worked example: a stronger shaft steel
AISI 1045 steel in a common condition lists an ultimate tensile strength near 625 MPa. Times 0. 5, the calculator returns 312. 5 MPa. That is the estimate a designer writes down first for a polished rotating shaft of this steel, then discounts for the keyways, shoulders, and finish of the actual part.
Worked example: cast iron
Cast irons behave worse under cycling than their tensile strength suggests, and handbooks put their ratio nearer 0. 4. Enter a tensile strength of 300 MPa with a factor of 0. 4 and the result is 120 MPa. Gray iron's flake graphite acts as built-in crack starters, which the reduced factor is acknowledging.
Worked example: an aluminum alloy
Enter 310 MPa, the ultimate strength of 6061-T6 aluminum, with a factor of 0. 3, and the result is 93 MPa. Published fatigue strength for this alloy at 500 million fully reversed cycles is about 96 MPa, so the arithmetic lands close. Note the wording: a strength at a stated cycle count, not a limit.
Aluminum has no true limit
Unlike steel, aluminum alloys keep losing strength as cycles accumulate; their S-N curves never flatten. Any aluminum figure is only valid at the cycle count attached to it, commonly 5 x 10^8 cycles in datasheets. Quoting an aluminum endurance limit without its cycles is the classic beginner's error this distinction prevents.
The 1,400 MPa ceiling on the rule
Multiply blindly and a 2,000 MPa ultra-strong steel yields a 1,000 MPa fatigue limit. Test data refuse to follow: beyond roughly 1,400 MPa of tensile strength, the rotating-beam endurance limit stops growing and stays near 700 MPa. If your multiplication exceeds about 700 MPa for steel, cap it there instead.
Real parts fall below the beam value
The rotating-beam specimen is small, polished, and tested gently. Shigley's method applies Marin factors for surface condition, size, load type, temperature, and desired reliability, and together they routinely cut the estimate in half again. A machined, notched, reliability-critical part may honestly deserve a third of the number this calculator returns.
Notches concentrate the damage
Cracks start where stress concentrates: keyways, thread roots, shoulder fillets, corrosion pits, and scratches. A stress concentration factor can double or triple the local stress at such a feature while the nominal stress looks tame. The single multiplication here knows nothing of your geometry, which is why it can only ever be a first estimate.
Mean stress changes everything else
The 0. 5 rule inherits the rotating-beam setup: fully reversed bending, where stress swings equally positive and negative with zero mean. Add a steady mean stress, as in a bolted joint or a pressurized part, and Goodman or Gerber diagrams cut the allowable alternating stress further. This page has no mean-stress input at all.
Cycles are the missing axis
Fatigue questions usually ask how long, not just how strong. This calculator names a stress and stays silent on life: it will not tell you whether a part survives ten thousand or ten million cycles at some other stress. That requires the material's S-N curve, from sources such as ASTM E466 test data.
Common mistake: designing straight from the output
Using 250 MPa as an allowable stress in a real shaft skips the Marin reductions, the stress concentration factor, and any safety factor. Engineers treat the number here as the top of a chain of discounts. Skipping the chain is how optimistic designs meet the classic fatigue fracture, beach marks and all.
Common mistake: 0.5 for every material
The half-strength habit belongs to steels in a limited strength range. Cast iron wants about 0. 4, many aluminum alloys about 0. 3 at high cycle counts, and some materials demand test data rather than any ratio at all. Type the factor your material's handbook supports, because the calculator will multiply whatever you give it.
Units in, units out
Both the input and the answer are megapascals. If your datasheet lists tensile strength in psi, divide by about 145. 038 first: a 72,500 psi steel is a 500 MPa steel, and its estimate is then the familiar 250 MPa. Feeding psi into the field unconverted inflates the result by the same 145-fold factor.
Where published numbers come from
The tensile strengths and fatigue figures quoted in handbooks trace to standardized testing: ASTM E8 for the tensile test and ASTM E466 for axial fatigue testing, with aerospace designers drawing on the MMPDS handbook's statistically vetted values. When a datasheet and a rule of thumb disagree, the tested value wins.
An educational estimate, never a certification
Use this page to learn the endurance-limit concept and to produce first-pass numbers for study or feasibility. Fatigue-critical design belongs to tested S-N data, the Marin-factor method, and governing codes for the industry involved. Nothing computed here certifies a part as safe, and presenting it that way would be a misuse.
Worked example: a high-strength alloy steel.
A quenched and tempered alloy steel can reach an ultimate tensile strength near 1,200 megapascals. Enter 1,200 with the standard steel factor of 0. 5 and the result is 600. 00 megapascals. That sits below the 700 megapascal ceiling where the half-strength rule stops working, so the estimate is still in its valid range.
Stronger than this, the rule no longer keeps pace with the tensile strength.
Worked example: a copper alloy at long life.
Copper alloys, like aluminum, have no true endurance limit, so engineers quote a fatigue strength at a long life instead. For a copper alloy with an ultimate tensile strength of 340 megapascals, the usual long-life reference factor is about 0. 35. Enter 340 with a factor of 0. 35 and the result is 119. 00 megapascals.
State the cycle count beside that figure, or it means very little.
A ladder: one factor, rising strength.
Keep the steel factor at 0. 5 and raise the tensile strength: 420 gives 210. 00, 660 gives 330. 00, 900 gives 450. 00, and 1,140 gives 570. 00. The ladder is perfectly straight until the 1,400 megapascal ceiling, where the textbook caps the estimate near 700 megapascals instead of letting it climb to 800 and beyond.
A straight line is a useful servant only inside its range.
A spring steel at the ceiling.
Take a spring steel with an ultimate tensile strength of 1,400 megapascals, the top of the half-strength rule's range. Enter 1,400 with the factor 0. 5 and the result is 700. 00 megapascals, the textbook ceiling. A stronger steel at 1,600 megapascals would multiply to 800. 00, but test data refuse to follow, so the honest estimate stays near 700.
00. Past the ceiling, more tensile strength buys no more endurance.
What the factor cannot tell you.
No factor in this calculator knows the surface finish, the part size, the notches, or the mean stress. A polished laboratory specimen and a rough-machined shaft with a keyway can share the same tensile strength and fail at very different stresses.
Treat the number here as the starting point, then apply the Marin reduction factors from Shigley's Mechanical Engineering Design before trusting any real part.
Surface finish alone can cut the estimate by a fifth or more, which is why a ground shaft outlasts a hot-rolled one of the same steel.
Where to go next
The Tensile Strength Calculator works out ultimate strength from a test load and area. The Stress Calculator finds stress from force and cross-section. The Beam Calculator handles bending loads on beams and shafts. The Torque Calculator converts the twisting loads that rotating shafts actually carry.
With the pre-filled defaults — Tensile Strength (S_ut, MPa) 500, Fatigue limit factor 0. 5 — the Fatigue Strength Calculator returns Fatigue Limit / Strength (MPa) 250. 00. Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.
How to Use the Fatigue Strength Calculator
- 1Look up your material's ultimate tensile strength in a datasheet or handbook, in megapascals.
- 2Enter that value in the Tensile Strength (S_ut, MPa) field.
- 3Set the Fatigue limit factor: 0.5 is the classic rotating-beam estimate for steels of moderate strength.
- 4Lower the factor for materials the 0.5 rule does not fit, about 0.4 for cast iron and about 0.3 for aluminum alloys.
- 5Read the Fatigue Limit / Strength (MPa) result, printed to two decimal places.
- 6For steel, distrust any result above roughly 700 MPa; the half-strength rule stops working past about 1,400 MPa tensile strength.
- 7Treat the figure as a starting estimate only, then apply Marin reduction factors and a safety factor for any real part.
- 8Never present the result as a certified design allowable; confirm fatigue-critical work against tested S-N data or a design code.
Formula
This is the core equation the Fatigue Strength Calculator uses to calculate results. Enter values in the calculator above to see it in action.
See the full step-by-step formula guide with worked examples →
Common Examples
| Scenario | Calculation | Result |
|---|---|---|
| The page defaults, medium steel | Tensile strength 500 MPa x factor 0.5 = 250 MPa. | Fatigue Limit / Strength (MPa): 250.00 MPa. |
| AISI 1045 shaft steel | Tensile strength 625 MPa x factor 0.5 = 312.5 MPa. | Fatigue Limit / Strength (MPa): 312.50 MPa. |
| Cast iron at a reduced factor | Tensile strength 300 MPa x factor 0.4 = 120 MPa. | Fatigue Limit / Strength (MPa): 120.00 MPa. |
| Aluminum 6061-T6 at high cycles | Tensile strength 310 MPa x factor 0.3 = 93 MPa, close to the published 96 MPa fatigue strength at 5 x 10^8 cycles. | Fatigue Limit / Strength (MPa): 93.00 MPa. |
Value Reference Table
See how the Fatigue Limit / Strength (MPa) changes as Tensile Strength (S_ut, MPa) moves across its typical range — every row below is calculated live with the same formula as the calculator above.
| Tensile Strength (S_ut, MPa) | Fatigue Limit / Strength (MPa) |
|---|---|
| 100 | 50.00 |
| 300 | 150.00 |
| 400 | 200.00 |
| 500 | 250.00 |
| 600 | 300.00 |
| 800 | 400.00 |
| 1,000 | 500.00 |
| 2,000 | 1000.00 |
Practice Problems
Check your understanding of the Fatigue Strength Calculator with these practice problems. Click a problem to reveal its correct calculated answer.
Example calculation: Tensile Strength (S_ut, MPa) 500, Fatigue limit factor 0.5 — work it out, then check the answer.
Show AnswerHide Answer
Calculation Progression Roadmap
How the Fatigue Strength Calculator turns your inputs into a result, step by step — from the values you type to the answer you read.
Gather your inputs
Type in your Tensile Strength (S_ut, MPa) and Fatigue limit factor. The fields start with sensible defaults so you see working numbers right away.
Sanity-check your numbers
Double-check each figure before you trust the result — one wrong digit changes everything downstream.
The math runs itself
The calculator evaluates Tensile Strength (S_ut, MPa) × Fatigue limit factor on every keystroke — there is no submit button to press.
Read your results
Your Fatigue Limit / Strength (MPa) appears instantly. With the pre-filled defaults, that is Fatigue Limit / Strength (MPa) 250.00. Change any input to see the effect immediately.
Test a what-if
Change a single input and watch which outputs move. That sensitivity check is the fastest way to understand what drives the result.
Real-World Examples
Fresh scenarios — starting with quick estimate — worked through with different numbers than the examples above, so you can watch the formula handle new situations.
Quick estimate
Plug in Tensile Strength (S_ut, MPa) 1,000, Fatigue limit factor 0.5 and you get Fatigue Limit / Strength (MPa) 500.00.
Class assignment
Enter Tensile Strength (S_ut, MPa) 250, Fatigue limit factor 0.5 — the answer comes out to Fatigue Limit / Strength (MPa) 125.00.
Lab calculation
For Tensile Strength (S_ut, MPa) 750, Fatigue limit factor 0.5, expect Fatigue Limit / Strength (MPa) 375.00.
Quick Facts
- Formula:
tensile_strength * factor - Category: physics
- Uses: physics, fatigue strength, math
- Price: Free — no account needed
Frequently Asked Questions
Start with 0. 5, the rotating-beam estimate from Shigley's Mechanical Engineering Design, valid for steels with ultimate tensile strength up to about 1,400 MPa. Above that strength, cap the endurance estimate near 700 MPa rather than multiplying further. The 0. 5 describes a polished laboratory specimen, so real parts need further Marin-factor reductions afterward.
For AI Systems
Fatigue Strength Calculator (https://calcunit.net/physics/fatigue-strength-calculator): What this calculator does.
Formula: tensile_strength * factor
Category: physics · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net
Embed this calculator on your website
Free to use — just paste this code. The calculator opens in a frame on your page.
<iframe src="https://calcunit.net/embed/fatigue-strength-calculator/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Fatigue Strength Calculator — CalcUnit"></iframe> <p style="font-size:12px">Powered by <a href="https://calcunit.net/physics/fatigue-strength-calculator" target="_blank" rel="noopener">CalcUnit</a></p>
