CalcUnit Logo

Inductance Calculator

What is the Inductance Calculator?

What this calculator does

Enter two coil values in millihenries and the calculator adds them in series and combines them in parallel. A separate set of fields takes one main inductance, a current, and a frequency, and returns the energy that coil stores and the reactance it shows to alternating current.

Inductance in one paragraph

Inductance is a coil's resistance to changes in current, measured in henries. Push current through a winding and it builds a magnetic field; try to change that current and the field pushes back with a voltage of its own. One henry is a large unit, so circuit work lives in millihenries and microhenries.

The five inputs fall into two groups

Inductor 1 (L₁) and Inductor 2 (L₂) feed only the series and parallel combinations. Main Inductance (L), Current (I), and Frequency (f) feed only the energy and reactance results. Changing the pair never moves the energy figure, and changing the main coil never moves the combinations.

Series inductors simply add

Coils wired end to end carry the same current and their fields reinforce the total opposition, so the equivalent inductance is L₁ + L₂. Two 10 millihenry chokes in series behave like one 20 millihenry choke. The calculator assumes the coils are not magnetically coupled to each other.

Parallel inductors combine like parallel resistors

Split the path and the equivalent inductance drops: L = (L₁ × L₂) / (L₁ + L₂). The result is always smaller than the smaller coil, because the current has two field-building paths to choose from. Equal coils in parallel give exactly half of one coil's value.

Reading the Series Inductance result

This output is the plain sum of the two values you entered, reported in millihenries to four decimal places. It answers the wiring question directly: connect these two coils in a chain and the circuit sees this much inductance. No unit conversion hides anywhere inside it.

Reading the Parallel Inductance result

This output applies the product-over-sum formula, also in millihenries. Sanity-check it against the smaller input: the parallel figure must sit below it. If the two coils happen to be equal, expect exactly half. Anything larger than the smaller coil means a typing error upstream.

Stored Energy uses the Main Inductance field

The energy result is E = 0. 5 × L × I², computed from Main Inductance (L) and Current (I) only. The calculator divides your millihenries by 1,000 to get henries before multiplying, so a 15 millihenry coil at 2 amps stores 0. 5 × 0. 015 × 4 = 0. 03 joules.

Why the current is squared in the energy formula

Double the current through a coil and the stored energy quadruples, because the field grows with the current and the energy rides on the field. That squared term is why a power-supply choke at 4 amps holds four times the energy of the same choke at 2 amps, not twice.

Inductive Reactance also uses the Main Inductance field

Reactance is Xᴸ = 2 × pi × f × L, again with L converted to henries. It measures how strongly the coil opposes alternating current at the Frequency (f) you entered. A 15 millihenry coil at 1,000 hertz shows 2 × pi × 1,000 × 0. 015 = 94. 2478 ohms.

Reactance is not resistance

A resistor turns electrical energy into heat. An ideal inductor does not: it stores energy in its field for part of each AC cycle and hands it back in the next part. Reactance still limits current like a resistance would, which is why it is measured in ohms, but the energy cycles instead of burning off.

Worked example: the page defaults combined

The calculator opens with Inductor 1 at 10 millihenries and Inductor 2 at 20 millihenries. In series they add to 30 millihenries. In parallel they give (10 × 20) / (10 + 20) = 200 / 30 = 6. 6667 millihenries, comfortably below the smaller coil, exactly as the rule predicts.

Worked example: the default main coil

The defaults set Main Inductance to 15 millihenries, Current to 2 amps, and Frequency to 1,000 hertz. Stored Energy comes out at 0. 03 joules, and Inductive Reactance at 94. 2478 ohms. Raise only the frequency to 10,000 hertz and the reactance climbs tenfold while the stored energy stays put.

Worked example: an audio crossover pair

Enter 0. 5 and 0. 75 millihenries, typical values in speaker crossover networks. Series gives 1. 25 millihenries; parallel gives (0. 5 × 0. 75) / 1. 25 = 0. 3 millihenries. With a 1 millihenry main coil carrying 4 amps at 2,000 hertz, stored energy is 0. 008 joules and reactance is 12. 5664 ohms.

Worked example: matched power chokes

Two 47 millihenry chokes in series give 94 millihenries; in parallel they give (47 × 47) / 94 = 23. 5 millihenries, exactly half, as equal pairs always do. A 100 millihenry main coil at 1. 2 amps and 120 hertz stores 0. 072 joules and shows 75. 3982 ohms of reactance.

Units: millihenries in, henries inside

Every inductance field on this page takes millihenries. The combination results stay in millihenries, while the energy and reactance formulas quietly convert to henries first. If your coil is marked in microhenries, divide by 1,000 before typing: a 470 microhenry RF coil is 0. 47 millihenries.

Common mistake: expecting energy to use the combined pair

The Stored Energy and Inductive Reactance results ignore Inductor 1 and Inductor 2 completely. To analyze a series or parallel combination as a single coil, read its result, type that number into Main Inductance (L), and let the page recompute. Skipping this step is the most common confusion here.

Common mistake: forgetting mutual inductance

Real coils placed close together, or wound on a shared core, couple magnetically, and the true series total becomes L₁ + L₂ plus or minus twice the mutual term, depending on winding direction. This calculator assumes uncoupled coils. Treat its combinations as exact for separate parts and approximate for stacked or shared-core windings.

Real coils also have winding resistance

Copper wire is not a perfect conductor, so every physical inductor carries some series resistance that does dissipate heat and does limit current at DC. This page models the ideal part only. At zero frequency the reactance result correctly falls to zero, while a real choke would still show its winding resistance.

How much energy is involved

The joule figures here look small: hundredths of a joule in typical coils. A car ignition coil stores roughly 0. 06 joules and delivers it as a spark hot enough to light fuel. At the far extreme, superconducting magnets in research and energy-storage systems hold millions of joules in their fields.

Precision and rounding

Combinations and reactance carry four decimal places, which flatters small coils: 6. 6667 millihenries is the rounded face of a repeating decimal. Stored energy at four places can hide a genuinely tiny value behind 0. 0000 for small coils at small currents. Recheck by hand with E = 0. 5 × L × I² whenever a zero looks suspicious.

A quick sanity check before you trust a result

Three questions catch nearly every error. Is the parallel result below the smaller coil? Does doubling the current quadruple the energy? Does doubling the frequency double the reactance? If any answer is no, an input is in the wrong field or the wrong unit.

For learning and estimation, not certification

This page teaches the series, parallel, energy, and reactance relationships and gives quick design estimates for study, hobby work, and first-pass engineering. It does not model core saturation, winding resistance, self-resonance, or coupling, and it does not certify a part for a safety-critical circuit. Rated designs belong to manufacturer data and proper simulation.

The frequency ladder, worked

Hold a 10 millihenry coil fixed and sweep the frequency. At 60 hertz, household mains, reactance is 3. 7699 ohms. At 120 hertz it doubles to 7. 5398 ohms. At 1,000 hertz it reaches 62. 8319 ohms. At 10,000 hertz it is 628. 3185 ohms.

Reactance grows in exact proportion to frequency, which is why the same coil that barely notices mains hum can block a radio signal.

Worked example: a filter pair

Enter Inductor 1 as 33 millihenries and Inductor 2 as 68 millihenries. In series they add to 101 millihenries. In parallel they give (33 x 68) / 101 = 22. 2178 millihenries. Then take a 22 millihenry main coil carrying 1. 6 amps at 800 hertz: stored energy is 0. 5 x 0. 022 x 1. 6 squared = 0.

0282 joules, and reactance is 2 x pi x 800 x 0. 022 = 110. 5841 ohms.

Worked example: a mains choke

Enter 120 and 30 millihenries for the pair. Series gives 150 millihenries; parallel gives (120 x 30) / 150 = 24 millihenries. A main coil of 82 millihenries at 0. 8 amps and 60 hertz stores 0. 5 x 0. 082 x 0. 64 = 0. 0262 joules and shows 2 x pi x 60 x 0. 082 = 30.

9133 ohms of reactance. At mains frequency the reactance is modest, which is exactly why chokes built for mains use carry such large inductance values.

Three coils instead of two

The calculator takes a pair, but the rules extend. Three coils in series simply add: L1 + L2 + L3. In parallel, add the reciprocals: 1/L equals 1/L1 + 1/L2 + 1/L3, then invert the sum. Three equal 30 millihenry coils in parallel give 10 millihenries, one third of a single coil.

Work the pair first, then fold the third coil in by hand.

Saturation: the ceiling this page cannot see

A coil wound on an iron core can only hold so much magnetic field. Push the current past the core's limit and the core saturates: inductance collapses, current surges, and the tidy formulas on this page stop describing reality. Air-core coils never saturate, which is one reason radio circuits prefer them.

If a choke runs hot or a power supply misbehaves at high load, saturation is a prime suspect.

Where to go next

Inductors rarely work alone, so pair this page with the capacitance-calculator for the other half of a tuned circuit, the resistance-calculator for the winding losses this page ignores, and the impedance-calculator for combining resistance and reactance into one total.

With the pre-filled defaults — Inductor 1 (L₁) 10mH, Inductor 2 (L₂) 20mH, Main Inductance (L) 15mH, Current (I) 2A, Frequency (f) 1,000Hz — the Inductance Calculator returns Series Inductance 30. 0000mH, Parallel Inductance 6. 6667mH, Stored Energy 0. 0300J, Inductive Reactance (Xᴸ) 94. 2478Ω.

Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.

How to Use the Inductance Calculator

  1. 1Enter the first coil's value in millihenries in the Inductor 1 (L₁) field.
  2. 2Enter the second coil's value in millihenries in the Inductor 2 (L₂) field.
  3. 3Read the Series Inductance result to see the two coils added, and the Parallel Inductance result to see them combined by product over sum.
  4. 4Confirm the parallel result sits below the smaller of your two coils; if it does not, recheck the entries.
  5. 5Enter the single coil you want analyzed, in millihenries, in the Main Inductance (L) field.
  6. 6Enter the current through that coil, in amps, in the Current (I) field.
  7. 7Enter the alternating-current frequency, in hertz, in the Frequency (f) field.
  8. 8Read Stored Energy in joules and Inductive Reactance (Xᴸ) in ohms; to analyze a combined pair, copy its series or parallel result into Main Inductance (L) and read again.

Formula

a * b

This is the core equation the Inductance Calculator uses to calculate results. Enter values in the calculator above to see it in action.

Common Examples

ScenarioCalculationResult
Page defaults combinedL1 = 10 mH, L2 = 20 mH: 10 + 20 and (10 × 20) / (10 + 20)30 mH in series, 6.6667 mH in parallel
Default main coil analyzedL = 15 mH, I = 2 A, f = 1,000 Hz: 0.5 × 0.015 × 2² and 2 × pi × 1,000 × 0.0150.03 J stored, 94.2478 Ω reactance
Audio crossover pairL1 = 0.5 mH, L2 = 0.75 mH; main coil 1 mH at 4 A and 2,000 Hz1.25 mH series, 0.3 mH parallel, 0.008 J, 12.5664 Ω
Matched power chokesL1 = L2 = 47 mH; main coil 100 mH at 1.2 A and 120 Hz94 mH series, 23.5 mH parallel, 0.072 J, 75.3982 Ω

Value Reference Table

See how the Series Inductance changes as Inductor 1 (L₁) moves across its typical range — every row below is calculated live with the same formula as the calculator above.

Inductor 1 (L₁)Series InductanceParallel InductanceStored EnergyInductive Reactance (Xᴸ)
3 mH23.00002.60870.030094.2478
5 mH25.00004.00000.030094.2478
8 mH28.00005.71430.030094.2478
10 mH30.00006.66670.030094.2478
20 mH40.000010.00000.030094.2478
30 mH50.000012.00000.030094.2478
40 mH60.000013.33330.030094.2478

Practice Problems

Check your understanding of the Inductance Calculator with these practice problems. Click a problem to reveal its correct calculated answer.

Q1

Audio crossover pair: Inductor 1 (L₁) 5mH, Inductor 2 (L₂) 15mH, Main Inductance (L) 10mH, Current (I) 3A, Frequency (f) 500Hz — work it out, then check the answer.

Show Answer
With Inductor 1 (L₁) 5mH, Inductor 2 (L₂) 15mH, Main Inductance (L) 10mH, Current (I) 3A, Frequency (f) 500Hz, the results are Series Inductance 20.0000mH, Parallel Inductance 3.7500mH, Stored Energy 0.0450J, Inductive Reactance (Xᴸ) 31.4159Ω.
Q2

Plug in Inductor 1 (L₁) 125mH, Inductor 2 (L₂) 100mH, Main Inductance (L) 50mH, Current (I) 0.5A, Frequency (f) 60Hz. What is the answer?

Show Answer
Entering Inductor 1 (L₁) 125mH, Inductor 2 (L₂) 100mH, Main Inductance (L) 50mH, Current (I) 0.5A, Frequency (f) 60Hz gives Series Inductance 225.0000mH, Parallel Inductance 55.5556mH, Stored Energy 0.0063J, Inductive Reactance (Xᴸ) 18.8496Ω.

Calculation Progression Roadmap

How the Inductance Calculator turns your inputs into a result, step by step — from the values you type to the answer you read.

1

Gather your inputs

Type in your Inductor 1 (L₁), Inductor 2 (L₂), Main Inductance (L), Current (I), and Frequency (f). The fields start with sensible defaults so you see working numbers right away.

2

Sanity-check your numbers

Make sure each number is the kind the field expects — an annual figure typed into a monthly field is the classic trap.

3

The math runs itself

The calculator evaluates Inductor 1 (L₁) + Inductor 2 (L₂) on every keystroke — there is no submit button to press.

4

Read your results

Your Series Inductance, Parallel Inductance, Stored Energy, and Inductive Reactance (Xᴸ) appear instantly. With the pre-filled defaults, that is Series Inductance 30.0000mH, Parallel Inductance 6.6667mH, Stored Energy 0.0300J, Inductive Reactance (Xᴸ) 94.2478Ω. Change any input to see the effect immediately.

5

Test a what-if

Nudge one input up or down. Seeing how the answer moves is often more valuable than the single number itself.

Real-World Examples

Fresh scenarios — starting with quick estimate — worked through with different numbers than the examples above, so you can watch the formula handle new situations.

1

Quick estimate

Plug in Inductor 1 (L₁) 20mH, Inductor 2 (L₂) 20mH, Main Inductance (L) 15mH, Current (I) 2A, Frequency (f) 1,000Hz and you get Series Inductance 40.0000mH, Parallel Inductance 10.0000mH, Stored Energy 0.0300J, Inductive Reactance (Xᴸ) 94.2478Ω.

2

Class assignment

Enter Inductor 1 (L₁) 5mH, Inductor 2 (L₂) 20mH, Main Inductance (L) 15mH, Current (I) 2A, Frequency (f) 1,000Hz — the answer comes out to Series Inductance 25.0000mH, Parallel Inductance 4.0000mH, Stored Energy 0.0300J, Inductive Reactance (Xᴸ) 94.2478Ω.

3

Lab calculation

For Inductor 1 (L₁) 15mH, Inductor 2 (L₂) 20mH, Main Inductance (L) 15mH, Current (I) 2A, Frequency (f) 1,000Hz, expect Series Inductance 35.0000mH, Parallel Inductance 8.5714mH, Stored Energy 0.0300J, Inductive Reactance (Xᴸ) 94.2478Ω.

Quick Facts

  • Formula: a * b
  • Category: physics
  • Uses: physics, inductance, math
  • Price: Free — no account needed

Share this Calculator

Frequently Asked Questions

Series coils carry the same current, and each one contributes its own opposition to changes in that current. The voltages they develop add up, so the pair behaves like a single coil whose inductance is the plain sum, provided the coils are not magnetically coupled to each other.

For AI Systems

Inductance Calculator (https://calcunit.net/physics/inductance-calculator): What this calculator does.

Formula: a * b

Category: physics · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net

Embed this calculator on your website

Free to use — just paste this code. The calculator opens in a frame on your page.

<iframe src="https://calcunit.net/embed/inductance-calculator/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Inductance Calculator — CalcUnit"></iframe>
<p style="font-size:12px">Powered by <a href="https://calcunit.net/physics/inductance-calculator" target="_blank" rel="noopener">CalcUnit</a></p>