CalcUnit Logo

Fluid Dynamics Calculator

What is the Fluid Dynamics Calculator?

What this calculator does

Give the calculator a fluid density, an upstream area and velocity, and a second, different area. It applies the continuity equation to find the velocity at the second section, reports the volume flow rate, and uses Bernoulli's equation to estimate the pressure difference between the two sections.

The continuity equation comes first

For an incompressible fluid in steady flow, what flows in must flow out: A₁ × v₁ = A₂ × v₂. Shrink the area and the fluid speeds up in exact inverse proportion. Halve the area and the velocity doubles. This one relationship runs every result on the page.

Velocity at Section 2

The first output rearranges continuity: v₂ = A₁ × v₁ / A₂. With the default areas, 0. 05 square meters shrinking to 0. 02, the velocity multiplies by two and a half. Note the assumption baked in: the same fluid, at the same density, filling both sections completely, with no leaks or branches between them.

Volume Flow Rate

The second output is Q = A₁ × v₁, the volume passing any section each second, in cubic meters per second. It equals A₂ × v₂ at the other section, which is the whole point of continuity. Multiply by 1,000 for liters per second, or by 60 for cubic meters per minute.

Mass flow rate follows from Q

Multiply the volume flow rate by density and you get mass flow, kilograms per second, the figure chemical and process engineers usually work in. The default water case moves 100 kilograms every second. This calculator leaves that one multiplication to you, but it is why density sits among the inputs at all.

The Bernoulli pressure drop

The third output is ΔP = 0. 5 × ρ × (v₂² − v₁²), the pressure at the wide section minus the pressure at the narrow one, for a level pipe. Where the fluid speeds up, its pressure falls. Density finally enters here; the two kinematic results above never use it.

Reading the results at the page defaults

Water at 1,000 kilograms per cubic meter flows at 2 meters per second through 0. 05 square meters, then through 0. 02. Velocity at the throat is 5 meters per second, flow rate is 0. 1 cubic meters per second, 100 liters every second, and the pressure drop is 10,500 pascals.

Worked example: a venturi section

Keep water but widen the entry: area 0. 08 square meters at 1. 2 meters per second, narrowing to 0. 02. The throat velocity is 4. 8 meters per second, the flow rate is 0. 096 cubic meters per second, and the pressure drop is 10,800 pascals. Venturi meters turn this pressure difference into a flow measurement.

Worked example: air in a duct

Air at 1. 225 kilograms per cubic meter moves at 6 meters per second through half a square meter, then through a quarter. Velocity doubles to 12 meters per second, flow rate is 3 cubic meters per second, and the pressure drop is 66. 15 pascals, because air is about 800 times less dense than water.

Worked example: gasoline in a fuel line

Gasoline at about 750 kilograms per cubic meter flows at 3 meters per second through 0. 01 square meters, narrowing to 0. 004. The velocity reaches 7. 5 meters per second and the pressure drop is 17,718. 75 pascals. Lighter than water, gasoline still produces a larger drop here because the velocity gain is bigger.

Worked example: a garden hose nozzle

A 25 millimeter hose has area 0. 000491 square meters; a 10 millimeter nozzle, 0. 0000785. Water entering at 1. 6 meters per second leaves the nozzle at 10 meters per second, six and a quarter times faster, with flow rate 0. 0007854 cubic meters per second and an ideal pressure drop of 48,720 pascals.

When the pressure drop comes out negative

Widen section 2 instead of narrowing it: 0. 02 square meters at 2 meters per second expanding to 0. 05. The velocity falls to 0. 8 meters per second and the result is negative 1,680 pascals, meaning pressure rises in the wide section. Diffusers in ductwork and pump intakes exploit exactly this pressure recovery.

Getting areas from pipe diameters

The fields want cross-sectional areas, but pipes are sold by diameter. Area is pi times diameter squared over four: a 100 millimeter pipe has 0. 007854 square meters; a 50 millimeter pipe, 0. 0019635. Entering a diameter as an area inflates every result and is the classic error here.

Choosing the density to enter

Water is 1,000 kilograms per cubic meter near room temperature, seawater about 1,025, gasoline roughly 740 to 750, common oils 870 to 910, and air about 1. 225. Density shifts with temperature, and it scales the pressure result in direct proportion: a five percent density error becomes a five percent pressure error.

The assumptions you are accepting

Bernoulli's equation in this form assumes steady, incompressible flow with no friction, along a horizontal path. Real pipes lose pressure to wall friction, fittings, and turbulence, and this calculator has no friction factor, no pipe length, and no elevation input. Its pressure drop is the ideal, frictionless floor beneath the real figure.

What is not on this page

There is no Reynolds number, so the calculator cannot warn you about turbulence. There is no pump head, no viscosity, no compressible-flow correction, and no height difference between sections. Each was left out deliberately; the page answers the continuity-and-Bernoulli question for two sections of one stream, nothing more.

The same equations in the body and the sky

Clinicians and physiologists borrow the same pair of equations: a narrowed artery or airway raises local velocity, which is why narrowed valves produce audible murmurs and measurable pressure gradients. Aircraft pitot tubes run Bernoulli backward, turning a pressure difference into an airspeed. The physics is identical; only the plumbing changes.

Units discipline

Areas in square meters, velocities in meters per second, density in kilograms per cubic meter, and the pressure arrives in pascals. Divide pascals by 1,000 for kilopascals or by 100,000 for bar. Duct designers working in inches of water column divide by about 249: this page's 66. 15 pascal duct example is 0. 2656 inches of water.

Precision and honest limits

Results carry four decimal places, which suits the flow rate and velocity. The pressure figure deserves less trust than its decimals suggest, because the frictionless assumption, not rounding, is the dominant error, routinely tens of percent in long or rough pipe runs. Use the value for comparison and learning, not for sizing safety equipment.

A quick sanity check before you trust a result

A narrower second area must raise the velocity and drop the pressure. A wider one must do the opposite. The flow rate computed from either section must match. And setting both areas equal must give zero pressure drop. If any of these fail, an area was probably entered as a diameter.

For learning and estimation, not certification

This calculator teaches continuity and Bernoulli for study, hobby engineering, and first-pass estimates. It does not size pipes, pumps, or pressure-relief devices, and it does not meet any design code. Work that carries pressure, fuel, or people belongs to licensed engineers using full friction and safety models.

Worked example five: seawater in a cooling line

Enter a density of 1025, an upstream area of 0. 06, an upstream velocity of 1. 5, and a second area of 0. 015. The velocity at the second section is 6. 0 meters per second, the flow rate is 0. 09 cubic meters per second, or 90 liters every second, and the pressure drop is 17,296. 88 pascals.

Seawater is only slightly denser than fresh water, so the extra density adds a small lift to the pressure figure while the fourfold narrowing does most of the work.

Worked example six: oil in a hydraulic line

Enter a density of 880, an upstream area of 0. 03, an upstream velocity of 2. 5, and a second area of 0. 012. The velocity reaches 6. 25 meters per second, the flow rate is 0. 075 cubic meters per second, or 75 liters every second, and the pressure drop is 14,437. 50 pascals.

Oil is lighter than water, yet the drop stays large, because the velocity more than doubles and the pressure term grows with the square of that velocity.

Narrowing the throat, step by step

Hold water at a density of 1000, an upstream area of 0. 06, and an upstream velocity of 1. 5, then narrow the second area in stages. At 0. 05 square meters the velocity is 1. 8 meters per second and the drop is 495. 00 pascals. At 0. 04 it is 2. 25 meters per second and 1,406.

25 pascals. At 0. 03 it is 3. 0 meters per second and 3,375. 00 pascals. At 0. 02 it is 4. 5 meters per second and 9,000. 00 pascals. At 0. 012 it is 7. 5 meters per second and 27,000. 00 pascals. The flow rate stays 0.

09 cubic meters per second at every step, which is continuity holding its promise while the pressure pays the price.

Why the pressure drop grows faster than the velocity

Velocity grows in inverse proportion to area, but pressure grows with the square of velocity, so each extra narrowing costs more pressure than the last. In the ladder above, cutting the second area from 0. 05 to 0. 04 lifts the velocity by only 0. 45 meters per second yet nearly triples the drop.

That steepening curve is the practical reason pipe designers avoid sudden contractions: a modest gain in speed can demand a pump that must work far harder.

A quick cross-check with mass flow

Multiply the volume flow rate by the density and you get the mass passing each second, a figure that must match at both sections. In the seawater example, 0. 09 cubic meters per second times 1025 kilograms per cubic meter is 92. 25 kilograms per second. In the oil example, 0. 075 times 880 is 66 kilograms per second.

If your two sections ever disagree on mass flow, one of the areas or velocities was entered wrong, because no fluid is created or lost between them.

Where to go next

To work the Bernoulli side of the same problem in more depth, try the Bernoulli Calculator (bernoulli-calculator). To put the pressure result in context, try the Pressure Physics Calculator (pressure-physics-calculator).

For the density figure that scales every pressure answer, try the Density Calculator (density-calculator), and for the speed and flow figures on their own, try the Velocity Calculator (velocity-calculator) and the Molar Flow Calculator (molar-flow-calculator).

With the pre-filled defaults — Fluid Density (ρ) 1,000 kg/m³, Area at Section 1 (A₁) 0. 05 m², Velocity at Section 1 (v₁) 2 m/s, Area at Section 2 (A₂) 0. 02 m² — the Fluid Dynamics Calculator returns Velocity at Section 2 (v₂) 5. 0000 m/s, Volume Flow Rate (Q) 0. 1000 m³/s, Pressure Drop (Bernoulli) 10,500. 0000 Pa.

Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.

How to Use the Fluid Dynamics Calculator

  1. 1Enter the fluid's density in kilograms per cubic meter in the Fluid Density (ρ) field, using 1,000 for water or 1.225 for air.
  2. 2Enter the upstream cross-sectional area in square meters in the Area at Section 1 (A₁) field, computing it as pi × diameter² / 4 if you know the pipe diameter.
  3. 3Enter the upstream speed in meters per second in the Velocity at Section 1 (v₁) field.
  4. 4Enter the second cross-sectional area in square meters in the Area at Section 2 (A₂) field.
  5. 5Read the Velocity at Section 2 (v₂) result and confirm it moved inversely to the area change.
  6. 6Read the Volume Flow Rate (Q) result in cubic meters per second, and multiply by 1,000 if you want liters per second.
  7. 7Read the Pressure Drop (Bernoulli) result in pascals; a negative value means the second section is wider and pressure rises there instead.
  8. 8Compare the drop against your real system cautiously, remembering the calculator assumes no friction and no height change between sections.

Formula

a * b

This is the core equation the Fluid Dynamics Calculator uses to calculate results. Enter values in the calculator above to see it in action.

Common Examples

ScenarioCalculationResult
Page defaults, waterρ = 1,000 kg/m³, A₁ = 0.05 m², v₁ = 2 m/s, A₂ = 0.02 m²: v₂ = 0.05 × 2 / 0.02v₂ = 5 m/s, Q = 0.1 m³/s, drop = 10,500 Pa
Venturi section, waterA₁ = 0.08 m², v₁ = 1.2 m/s, A₂ = 0.02 m², ρ = 1,000 kg/m³v₂ = 4.8 m/s, Q = 0.096 m³/s, drop = 10,800 Pa
Air duct contractionρ = 1.225 kg/m³, A₁ = 0.5 m², v₁ = 6 m/s, A₂ = 0.25 m²v₂ = 12 m/s, Q = 3 m³/s, drop = 66.15 Pa
Widening diffuser, waterA₁ = 0.02 m², v₁ = 2 m/s, A₂ = 0.05 m², ρ = 1,000 kg/m³v₂ = 0.8 m/s, drop = −1,680 Pa (pressure rises)

Value Reference Table

See how the Velocity at Section 2 (v₂) changes as Fluid Density (ρ) moves across its typical range — every row below is calculated live with the same formula as the calculator above.

Fluid Density (ρ)Velocity at Section 2 (v₂)Volume Flow Rate (Q)Pressure Drop (Bernoulli)
300 kg/m³5.00000.10003150.0000
500 kg/m³5.00000.10005250.0000
800 kg/m³5.00000.10008400.0000
1,000 kg/m³5.00000.100010500.0000
2,000 kg/m³5.00000.100021000.0000
3,000 kg/m³5.00000.100031500.0000
4,000 kg/m³5.00000.100042000.0000

Practice Problems

Check your understanding of the Fluid Dynamics Calculator with these practice problems. Click a problem to reveal its correct calculated answer.

Q1

Garden hose narrowing: Plug in Fluid Density (ρ) 1,000 kg/m³, Area at Section 1 (A₁) 0.1 m², Velocity at Section 1 (v₁) 1.5 m/s, Area at Section 2 (A₂) 0.04 m². What is the answer?

Show Answer
Entering Fluid Density (ρ) 1,000 kg/m³, Area at Section 1 (A₁) 0.1 m², Velocity at Section 1 (v₁) 1.5 m/s, Area at Section 2 (A₂) 0.04 m² gives Velocity at Section 2 (v₂) 3.7500 m/s, Volume Flow Rate (Q) 0.1500 m³/s, Pressure Drop (Bernoulli) 5,906.2500 Pa.
Q2

Given Fluid Density (ρ) 1.53 kg/m³, Area at Section 1 (A₁) 0.5 m², Velocity at Section 1 (v₁) 10 m/s, Area at Section 2 (A₂) 0.25 m², what does it come out to?

Show Answer
The calculator returns Velocity at Section 2 (v₂) 20.0000 m/s, Volume Flow Rate (Q) 5.0000 m³/s, Pressure Drop (Bernoulli) 229.5000 Pa for Fluid Density (ρ) 1.53 kg/m³, Area at Section 1 (A₁) 0.5 m², Velocity at Section 1 (v₁) 10 m/s, Area at Section 2 (A₂) 0.25 m².

Calculation Progression Roadmap

How the Fluid Dynamics Calculator turns your inputs into a result, step by step — from the values you type to the answer you read.

1

Gather your inputs

Type in your Fluid Density (ρ), Area at Section 1 (A₁), Velocity at Section 1 (v₁), and Area at Section 2 (A₂). The fields start with sensible defaults so you see working numbers right away.

2

Sanity-check your numbers

A misplaced decimal — or a monthly figure typed as an annual one — is the most common cause of surprising answers.

3

The math runs itself

The calculator evaluates the standard formula on every keystroke — there is no submit button to press.

4

Read your results

Your Velocity at Section 2 (v₂), Volume Flow Rate (Q), and Pressure Drop (Bernoulli) appear instantly. With the pre-filled defaults, that is Velocity at Section 2 (v₂) 5.0000 m/s, Volume Flow Rate (Q) 0.1000 m³/s, Pressure Drop (Bernoulli) 10,500.0000 Pa. Change any input to see the effect immediately.

5

Test a what-if

Try a bigger and a smaller value for one input. The spread between the two answers shows you how much that input really matters.

Real-World Examples

Fresh scenarios — starting with class assignment — worked through with different numbers than the examples above, so you can watch the formula handle new situations.

1

Class assignment

Enter Fluid Density (ρ) 2,000 kg/m³, Area at Section 1 (A₁) 0.05 m², Velocity at Section 1 (v₁) 2 m/s, Area at Section 2 (A₂) 0.02 m² — the answer comes out to Velocity at Section 2 (v₂) 5.0000 m/s, Volume Flow Rate (Q) 0.1000 m³/s, Pressure Drop (Bernoulli) 21,000.0000 Pa.

2

Lab calculation

For Fluid Density (ρ) 500 kg/m³, Area at Section 1 (A₁) 0.05 m², Velocity at Section 1 (v₁) 2 m/s, Area at Section 2 (A₂) 0.02 m², expect Velocity at Section 2 (v₂) 5.0000 m/s, Volume Flow Rate (Q) 0.1000 m³/s, Pressure Drop (Bernoulli) 5,250.0000 Pa.

3

Homework problem

A quick run with Fluid Density (ρ) 1,500 kg/m³, Area at Section 1 (A₁) 0.05 m², Velocity at Section 1 (v₁) 2 m/s, Area at Section 2 (A₂) 0.02 m² gives Velocity at Section 2 (v₂) 5.0000 m/s, Volume Flow Rate (Q) 0.1000 m³/s, Pressure Drop (Bernoulli) 15,750.0000 Pa.

Quick Facts

  • Formula: a * b
  • Category: physics
  • Uses: physics, fluid dynamics, math
  • Price: Free — no account needed

Share this Calculator

Frequently Asked Questions

An incompressible fluid cannot pile up or leave gaps, so the same volume must pass every section each second. Volume per second is area times velocity; when the area shrinks, the velocity must grow to keep the product constant. Halving the area exactly doubles the velocity, which the Velocity at Section 2 result shows directly.

For AI Systems

Fluid Dynamics Calculator (https://calcunit.net/physics/fluid-dynamics-calculator): What this calculator does.

Formula: a * b

Category: physics · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net

Embed this calculator on your website

Free to use — just paste this code. The calculator opens in a frame on your page.

<iframe src="https://calcunit.net/embed/fluid-dynamics-calculator/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Fluid Dynamics Calculator — CalcUnit"></iframe>
<p style="font-size:12px">Powered by <a href="https://calcunit.net/physics/fluid-dynamics-calculator" target="_blank" rel="noopener">CalcUnit</a></p>