Percent Error Calculator
What is the Percent Error Calculator?
What this calculator measures
Give it an Observed Value and the Actual (True) Value it should have matched, and this page reports the Absolute Error and the Percent Error between them. It opens with an observed 9. 8 against an actual 10: an absolute error of 0. 2 and a percent error of 2 percent.
The two values it asks for
Observed Value is the number your instrument, scale, or experiment actually produced. Actual (True) Value is the accepted reference you compare against, from a textbook constant, a calibration certificate, or a trusted standard. Both sit in the Values group, and the two results sit in the Error group.
The default run, worked in full
The gap between 9. 8 and 10 is 0. 2, and the Absolute Error line shows it as a positive 0. 2000. Divide that gap by the actual value and multiply by 100: 0. 2 divided by 10, times 100, gives a Percent Error of 2. 0000 percent. Both lines show four decimal places.
The absolute error here never carries a sign
The field's help wording describes a subtraction, actual minus observed, but the formula takes the absolute value of the difference, so the line always prints a positive size. An observed 9. 8 and an observed 10. 2 against an actual 10 both print 0. 2000, one low and one high.
Percent error divides by the actual value
The base of the percentage is always the accepted value, never your reading. That is why the same gap of 0. 2 is 2 percent of an actual 10 but only 0. 02 percent of an actual 1,000. Your measurement is being priced against the size of the thing measured.
The direction of the miss stays hidden
Nothing on the page says whether you read high or low. Work it out by hand with the signed error, observed minus actual. On the default run that is 9. 8 minus 10, a signed error of negative 0. 2, so the measurement read low. Direction matters when you adjust an instrument.
Swapping the two values changes the answer
The actual value is the divisor, so it matters which number goes where. Observed 10 against actual 9. 8 gives 0. 2 divided by 9. 8, a percent error of 2. 0408 percent, not 2. If a result looks slightly off, check that the accepted value sits in the Actual (True) Value field.
A zero actual value has no guard
Enter an actual value of 0, with an observed 5 or an observed 0, and the Percent Error line cannot compute: it shows a dash instead. Percent error against a value of zero is undefined in mathematics too. Report the absolute error, which still computes, and describe the miss in plain units.
Negative actual values still behave
The denominator uses the absolute value of the actual value, so the percent error stays positive and sensible. An observed negative 19 against an actual negative 20 prints an absolute error of 1 and a percent error of 5 percent. Tools that divide by the signed value would print a confusing negative error here.
Percent error can pass 100 percent
Observe 25 against an actual 10 and the absolute error is 15, one and a half times the thing measured, giving a percent error of 150. That usually signals a blunder, a swapped input, or a unit mismatch rather than a merely sloppy measurement, so check the setup before blaming the instrument.
Units must match before you type
The page converts nothing. An observed value in millimeters subtracted from an actual value in centimeters mixes two scales and prints a meaningless error. Convert one value first so both sit in the same unit. The percent error itself then carries no unit, being a ratio of two like quantities.
The same miss shrinks as the target grows
An absolute error of 0. 2 is 2 percent of an actual 10, but only 0. 02 percent of an actual 1,000. That is the entire point of the percent form: it prices the miss against the size measured, so very different measurements can be compared fairly on one scale.
Four decimal places are display, not honesty
Both lines show four decimal places, so a stopwatch reading to hundredths still prints a percent error like 1. 1186. Report only the significant figures your instrument earned. Extra digits copied into a lab report claim a precision the measurement never had, and careful readers will notice the mismatch.
Average repeated readings first, by hand
The page compares one observed value with one actual value. With five trials, average the five readings and enter the mean as the Observed Value. The spread among the trials is a separate question about precision, repeatability rather than accuracy, and no output on this page describes it at all.
Where the actual value comes from
Accepted values come from calibration certificates, standard references, and trusted instruments: standard gravity of 9. 80665 meters per second squared, or water boiling at 100 degrees Celsius at standard pressure. If the reference itself is shaky, the percent error inherits that doubt, and no arithmetic on this page can repair it.
Percent error is not percentage points
If one instrument errs by 2 percent and another by 3 percent, the gap between them is one percentage point, while the second error is 50 percent larger than the first. Keep the two languages separate in reports. This page speaks percent error; comparing two percent errors uses points.
A quick mental check
One percent of the actual 10 is 0. 1, and the absolute error is 0. 2, so a 2 percent answer hangs together. Estimate one percent of your actual value before reading the screen. If the printed percent error is wildly off that scale, an input is probably swapped or in the wrong unit.
Relative error is the same fact as a fraction
Divide the percent error by 100 to get the relative error: 2 percent is 0. 02. This page has no separate relative error line and no accuracy score. If you need an accuracy figure, the shortcut is 100 minus the percent error, 98 on the default run, computed by hand.
What counts as a good percent error
Many school and undergraduate labs accept results under about 5 percent, routine workshop checks may demand 1 to 2 percent, and calibration work often targets 0. 1 percent or tighter. The bar belongs to your task, your instrument, or your instructor, not to this page. Judge your result against that bar.
What this page cannot do
It cannot show a signed error, average trials, propagate uncertainty through a longer calculation, or judge whether your accepted value deserves trust. It answers one narrow question well: how large is this single miss, first in your own units and then as a percentage of the accepted value. That is the whole job.
With the pre-filled defaults — Observed Value 9. 8, Actual (True) Value 10 — the Percent Error Calculator returns Absolute Error 0. 2000, Percent Error 2. 0000%. Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.
How to Use the Percent Error Calculator
- 1Enter your measured or experimental number in the Observed Value field.
- 2Enter the accepted reference in the Actual (True) Value field.
- 3Confirm both values use the same unit before reading any result.
- 4Read Absolute Error for the size of the miss, in your own unit.
- 5Read Percent Error for the same miss as a percentage of the actual value.
- 6Work out the direction by hand, observed minus actual, if high or low matters.
- 7If the actual value is zero, ignore the percent line and report the absolute error.
- 8For repeated trials, average the readings first and enter the mean as observed.
Formula
This is the core equation the Percent Error Calculator uses to calculate results. Enter values in the calculator above to see it in action.
See the full step-by-step formula guide with worked examples →
Common Examples
| Scenario | Calculation | Result |
|---|---|---|
| Measured density 8.74 against an accepted 8.96 | Absolute error = |8.74 - 8.96| = 0.22; percent error = 0.22 / 8.96 x 100 = 2.455357 | Absolute Error 0.22, Percent Error 2.4554% |
| Truck scale reads 152.4 against a true 150 | Absolute error = |152.4 - 150| = 2.4; percent error = 2.4 / 150 x 100 = 1.6 | Absolute Error 2.4, Percent Error 1.6% |
| Thermometer reads 99.2 in water boiling at 100 | Absolute error = |99.2 - 100| = 0.8; percent error = 0.8 / 100 x 100 = 0.8 | Absolute Error 0.8, Percent Error 0.8% |
| Timed fall of 0.452 seconds against a true 0.447 | Absolute error = |0.452 - 0.447| = 0.005; percent error = 0.005 / 0.447 x 100 = 1.118568 | Absolute Error 0.005, Percent Error 1.1186% |
Value Reference Table
See how the Absolute Error changes as Observed Value moves across its typical range — every row below is calculated live with the same formula as the calculator above.
| Observed Value | Absolute Error | Percent Error |
|---|---|---|
| 5 | 5.0000 | 50.0000 |
| 10 | 0.0000 | 0.0000 |
| 15 | 5.0000 | 50.0000 |
| 20 | 10.0000 | 100.0000 |
| 25 | 15.0000 | 150.0000 |
| 30 | 20.0000 | 200.0000 |
| 40 | 30.0000 | 300.0000 |
| 50 | 40.0000 | 400.0000 |
| 75 | 65.0000 | 650.0000 |
| 100 | 90.0000 | 900.0000 |
Practice Problems
Check your understanding of the Percent Error Calculator with these practice problems. Click a problem to reveal its correct calculated answer.
Physics experiment: You enter Observed Value 9.8, Actual (True) Value 10 — what does the calculator return?
Show AnswerHide Answer
With Observed Value 6.06, Actual (True) Value 5, what are the results?
Show AnswerHide Answer
Measurement error: Observed Value 102, Actual (True) Value 100 — work it out, then check the answer.
Show AnswerHide Answer
Calculation Progression Roadmap
How the Percent Error Calculator turns your inputs into a result, step by step — from the values you type to the answer you read.
Gather your inputs
Type in your Observed Value and Actual (True) Value. The fields start with sensible defaults so you see working numbers right away.
Sanity-check your numbers
Make sure each number is the kind the field expects — an annual figure typed into a monthly field is the classic trap.
The math runs itself
The calculator evaluates abs(Observed Value-Actual (True) Value) on every keystroke — there is no submit button to press.
Read your results
Your Absolute Error and Percent Error appear instantly. With the pre-filled defaults, that is Absolute Error 0.2000, Percent Error 2.0000%. Change any input to see the effect immediately.
Test a what-if
Nudge one input up or down. Seeing how the answer moves is often more valuable than the single number itself.
Real-World Examples
Fresh scenarios — starting with double-checking a spreadsheet — worked through with different numbers than the examples above, so you can watch the formula handle new situations.
Double-checking a spreadsheet
A quick run with Observed Value 19.6, Actual (True) Value 10 gives Absolute Error 9.6000, Percent Error 96.0000%.
Settling a debate
With Observed Value 4.9, Actual (True) Value 10, the calculator returns Absolute Error 5.1000, Percent Error 51.0000%.
Quick mental-math verify
Plug in Observed Value 14.7, Actual (True) Value 10 and you get Absolute Error 4.7000, Percent Error 47.0000%.
Quick Facts
- Formula:
|Observed-Actual|/Actual × 100 - Category: math
- Uses: percent error, error, accuracy
- Price: Free — no account needed
Frequently Asked Questions
Both the difference and the actual value pass through an absolute value in the formula, so the result describes size only. A reading 0. 2 low and a reading 0. 2 high against an actual 10 both print 2 percent. Direction needs the signed subtraction, done by hand.
For AI Systems
Percent Error Calculator (https://calcunit.net/math/percent-error-calculator): What this calculator measures.
Formula: |Observed-Actual|/Actual × 100
Category: math · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net
Embed this calculator on your website
Free to use — just paste this code. The calculator opens in a frame on your page.
<iframe src="https://calcunit.net/embed/percent-error-calculator/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Percent Error Calculator — CalcUnit"></iframe> <p style="font-size:12px">Powered by <a href="https://calcunit.net/math/percent-error-calculator" target="_blank" rel="noopener">CalcUnit</a></p>
