Motor Calculator
What is the Motor Calculator?
What this calculator does
Enter the supply voltage, armature current, armature resistance, and speed of a direct current motor, and this page returns back EMF, input power, copper loss, mechanical power, efficiency, angular speed, and torque. It sits in the math section, but the content is electrical engineering: a DC motor model, not an algebra topic.
The honest scope, stated first
This is a simple steady state DC motor model. It assumes one armature resistance, ignores brush voltage drop, iron losses, friction, and windage, and treats the values you enter as already settled running values. It suits homework, hobby sizing, and quick estimates. It is not a design tool for industrial drives or safety decisions.
The four inputs it asks for
Supply Voltage is in volts. Armature Current is in amps. Armature Resistance is in ohms, usually a small fraction of an ohm for larger machines. Speed is in revolutions per minute. The page opens with 24 volts, 5 amps, 0. 5 ohms, and 1,500 rpm, a small workshop sized motor.
Back EMF, the first result
A spinning motor acts partly like a generator, producing a voltage that opposes the supply, called back EMF. The page computes it as supply voltage minus current times resistance: 24 minus 5 times 0. 5 equals 21. 5000 volts. The gap between supply and back EMF is the voltage that drives current through the resistance.
Input power and copper loss
Input Power is simply voltage times current: 24 times 5 equals 120. 0000 watts drawn from the supply. Copper Loss is current squared times resistance: 25 times 0. 5 equals 12. 5000 watts, wasted as heat in the windings. Copper loss grows with the square of current, so doubling current quadruples the heating.
Mechanical power developed
Mechanical Power is back EMF times current: 21. 5 times 5 equals 107. 5000 watts. Notice the bookkeeping closes perfectly: input 120 minus copper loss 12. 5 equals 107. 5. On this simple model, copper loss is the only loss, so every remaining watt becomes mechanical power developed inside the machine.
Efficiency, as this page defines it
Efficiency is mechanical power divided by input power, times 100: here 89. 5833 percent. It also equals back EMF divided by supply voltage, a shortcut. Read it as an electrical conversion efficiency only. A real motor loses more to friction, iron, and stray effects, so its true shaft efficiency is lower than this figure.
Angular speed conversion
Speed in rpm becomes radians per second by multiplying by 2 pi and dividing by 60. At 1,500 rpm that gives 157. 0796 radians per second. This line is a pure unit conversion, needed because torque uses radians per second, not revolutions per minute.
Torque from power and speed
Torque is mechanical power divided by angular speed: 107. 5 divided by 157. 0796 equals 0. 6844 newton meters for the defaults. Same power at lower speed means higher torque, which is why geared down motors pull so hard. This is developed torque, so shaft torque on a real motor is smaller.
Worked example: a twelve volt motor
Enter 12 volts, 2 amps, resistance 1 ohm, and 3,000 rpm. Back EMF is 10. 0000 volts. Input power is 24. 0000 watts, copper loss is 4. 0000, mechanical power is 20. 0000, and efficiency is 83. 3333 percent. Torque is 0. 0637 newton meters.
Worked example: a forty eight volt traction motor
Enter 48 volts, 10 amps, resistance 0. 2 ohms, and 2,000 rpm. Back EMF is 46. 0000 volts. Input power is 480. 0000 watts, copper loss is 20. 0000, mechanical power is 460. 0000, and efficiency is 95. 8333 percent. Torque is 2. 1963 newton meters.
Worked example: a thirty six volt motor under load
Enter 36 volts, 8 amps, resistance 0. 75 ohms, and 1,800 rpm. Back EMF is 30. 0000 volts. Input power is 288. 0000 watts, copper loss is 48. 0000, mechanical power is 240. 0000, and efficiency is 83. 3333 percent. Torque is 1. 2732 newton meters.
Why speed does not change the electrical lines
Voltage, current, resistance, and back EMF are linked without speed in this model, so changing rpm alone moves only angular speed and torque. In a real motor, speed and back EMF rise together. Here you supply both independently, so keep them physically consistent yourself.
The stalled motor warning
At standstill a motor has no back EMF, draws a starting current, and can overheat. This page cannot show that: enter speed 0 and torque reads 0 by a guard, while the electrical lines still use the current you typed. The current is your input, not a prediction, so a stall must be reasoned by hand.
When back EMF goes negative
If current times resistance exceeds the supply voltage, back EMF turns negative and mechanical power and efficiency follow it below zero. That combination cannot describe a motor running normally on that supply; it signals mismatched inputs, like a current copied from a bigger machine. Negative outputs are an input audit alarm, not a physical result.
Starting current, estimated by hand
At the instant of switching on, back EMF is zero, so current is supply voltage divided by armature resistance. The default motor would draw 24 over 0. 5, or 48 amps, nearly ten times its running current, which is why drives add starters or soft start controllers. This page models running conditions, not that surge.
Regenerative braking explained
Force a motor to spin faster than its natural speed for the supply and back EMF passes the supply voltage, current reverses, and the machine generates, returning energy to the supply or a battery. The formulas still balance with signed current, but the page labels assume motoring. Treat generating cases as hand analysis.
Units and typical values
Work in volts, amps, ohms, rpm, watts, radians per second, and newton meters, as the labels state. Armature resistance is often well under 1 ohm, so expect small decimals and measure it carefully; a cheap meter reading leads included can double it. Torque in newton meters converts to pound feet by multiplying by about 0. 7376.
Efficiency cannot pass one hundred
On this model efficiency is back EMF over supply voltage. Back EMF below the supply gives a figure under 100 percent, and equal back EMF would mean zero power. Any result over 100 percent means inconsistent inputs were entered, since no machine returns more mechanical power than it receives.
Temperature changes the resistance
Copper resistance rises about 0. 393 percent per degree Celsius, so a hot winding resists more and loses more. The page takes resistance as a fixed input. For careful work, enter the hot resistance you expect at running temperature, often twenty to forty percent above the cold measurement.
Where these formulas come from
The model is the standard armature circuit taught in electrical machines courses: supply equals back EMF plus the resistance drop, from Kirchhoff voltage law, with power balances built on top. Standard course texts use this same first model before adding loss terms. Nothing here is a proprietary method or a special CalcUnit invention.
Checking the whole run
Four checks validate everything. Input power minus copper loss equals mechanical power. Efficiency equals back EMF over voltage, as a percent. Torque times angular speed returns mechanical power. And back EMF stays positive and below the supply for a normally running motor. Run those before quoting torque or efficiency anywhere that matters.
When to use a fuller model instead
Step up to manufacturer curves or a full engineering tool when you need shaft output rather than developed power, starting and stall behavior, heating, gearbox losses, or alternating current machines. This page knows one machine type, the brushed DC motor in steady running, and AC induction and brushless motors need different equations entirely.
With the pre-filled defaults — Supply Voltage 24V, Armature Current 5A, Armature Resistance 0. 5Ω, Speed 1,500rpm — the Motor Calculator returns Back EMF 21. 5000V, Input Power 120. 0000W, Copper Loss (I²R) 12. 5000W, Mechanical Power 107. 5000W, Efficiency 89. 5833%, and 2 more more results.
Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.
How to Use the Motor Calculator
- 1Enter the DC supply voltage in the Supply Voltage field, in volts.
- 2Enter the running armature current in the Armature Current field, in amps.
- 3Enter the winding resistance in the Armature Resistance field, in ohms.
- 4Enter the running speed in the Speed field, in revolutions per minute.
- 5Read Back EMF for voltage minus current times resistance.
- 6Read Input Power, Copper Loss (I squared R), and Mechanical Power, checking input minus loss equals mechanical.
- 7Read Efficiency and Angular Speed, then read Torque for mechanical power over angular speed.
- 8Confirm back EMF is positive and below the supply voltage before trusting the run.
Formula
This is the core equation the Motor Calculator uses to calculate results. Enter values in the calculator above to see it in action.
Common Examples
| Scenario | Calculation | Result |
|---|---|---|
| Page default workshop motor | V 24, I 5, R 0.5, 1500 rpm: E = 24 - 5 x 0.5 = 21.5, input = 120, copper loss = 25 x 0.5 = 12.5 | Back EMF 21.5000, Input Power 120.0000, Copper Loss 12.5000, Mechanical Power 107.5000, Efficiency 89.5833, Angular Speed 157.0796, Torque 0.6844 |
| Small 12 volt motor | V 12, I 2, R 1, 3000 rpm: E = 12 - 2 x 1 = 10, input = 24, copper loss = 4 x 1 = 4 | Back EMF 10.0000, Input Power 24.0000, Copper Loss 4.0000, Mechanical Power 20.0000, Efficiency 83.3333, Angular Speed 314.1593, Torque 0.0637 |
| 48 volt traction motor | V 48, I 10, R 0.2, 2000 rpm: E = 48 - 10 x 0.2 = 46, input = 480, copper loss = 100 x 0.2 = 20 | Back EMF 46.0000, Input Power 480.0000, Copper Loss 20.0000, Mechanical Power 460.0000, Efficiency 95.8333, Angular Speed 209.4395, Torque 2.1963 |
| 36 volt motor under load | V 36, I 8, R 0.75, 1800 rpm: E = 36 - 8 x 0.75 = 30, input = 288, copper loss = 64 x 0.75 = 48 | Back EMF 30.0000, Input Power 288.0000, Copper Loss 48.0000, Mechanical Power 240.0000, Efficiency 83.3333, Angular Speed 188.4956, Torque 1.2732 |
Value Reference Table
See how the Back EMF changes as Supply Voltage moves across its typical range — every row below is calculated live with the same formula as the calculator above.
| Supply Voltage | Back EMF | Input Power | Copper Loss (I²R) | Mechanical Power | Efficiency | Angular Speed | Torque |
|---|---|---|---|---|---|---|---|
| 6 V | 3.5000 | 30.0000 | 12.5000 | 17.5000 | 58.3333 | 157.0796 | 0.1114 |
| 10 V | 7.5000 | 50.0000 | 12.5000 | 37.5000 | 75.0000 | 157.0796 | 0.2387 |
| 20 V | 17.5000 | 100.0000 | 12.5000 | 87.5000 | 87.5000 | 157.0796 | 0.5570 |
| 30 V | 27.5000 | 150.0000 | 12.5000 | 137.5000 | 91.6667 | 157.0796 | 0.8754 |
| 40 V | 37.5000 | 200.0000 | 12.5000 | 187.5000 | 93.7500 | 157.0796 | 1.1937 |
| 50 V | 47.5000 | 250.0000 | 12.5000 | 237.5000 | 95.0000 | 157.0796 | 1.5120 |
| 60 V | 57.5000 | 300.0000 | 12.5000 | 287.5000 | 95.8333 | 157.0796 | 1.8303 |
| 70 V | 67.5000 | 350.0000 | 12.5000 | 337.5000 | 96.4286 | 157.0796 | 2.1486 |
| 100 V | 97.5000 | 500.0000 | 12.5000 | 487.5000 | 97.5000 | 157.0796 | 3.1035 |
Practice Problems
Check your understanding of the Motor Calculator with these practice problems. Click a problem to reveal its correct calculated answer.
Small 12 V motor: Given Supply Voltage 12V, Armature Current 2A, Armature Resistance 1Ω, Speed 3,000rpm, what does it come out to?
Show AnswerHide Answer
You enter Supply Voltage 60V, Armature Current 10A, Armature Resistance 0.2Ω, Speed 2,000rpm — what does the calculator return?
Show AnswerHide Answer
Calculation Progression Roadmap
How the Motor Calculator turns your inputs into a result, step by step — from the values you type to the answer you read.
Gather your inputs
Type in your Supply Voltage, Armature Current, Armature Resistance, and Speed. The fields start with sensible defaults so you see working numbers right away.
Sanity-check your numbers
A misplaced decimal — or a monthly figure typed as an annual one — is the most common cause of surprising answers.
The math runs itself
The calculator evaluates Supply Voltage - Armature Current × Armature Resistance on every keystroke — there is no submit button to press.
Read your results
Your Back EMF, Input Power, Copper Loss (I²R), Mechanical Power, Efficiency, and 2 more more appear instantly. With the pre-filled defaults, that is Back EMF 21.5000V, Input Power 120.0000W, Copper Loss (I²R) 12.5000W, Mechanical Power 107.5000W, Efficiency 89.5833%, and 2 more more results. Change any input to see the effect immediately.
Test a what-if
Try a bigger and a smaller value for one input. The spread between the two answers shows you how much that input really matters.
Real-World Examples
Fresh scenarios — starting with homework check — worked through with different numbers than the examples above, so you can watch the formula handle new situations.
Homework check
For Supply Voltage 48V, Armature Current 5A, Armature Resistance 0.5Ω, Speed 1,500rpm, expect Back EMF 45.5000V, Input Power 240.0000W, Copper Loss (I²R) 12.5000W, Mechanical Power 227.5000W, Efficiency 94.7917%, and 2 more more results.
Double-checking a spreadsheet
A quick run with Supply Voltage 12V, Armature Current 5A, Armature Resistance 0.5Ω, Speed 1,500rpm gives Back EMF 9.5000V, Input Power 60.0000W, Copper Loss (I²R) 12.5000W, Mechanical Power 47.5000W, Efficiency 79.1667%, and 2 more more results.
Settling a debate
With Supply Voltage 36V, Armature Current 5A, Armature Resistance 0.5Ω, Speed 1,500rpm, the calculator returns Back EMF 33.5000V, Input Power 180.0000W, Copper Loss (I²R) 12.5000W, Mechanical Power 167.5000W, Efficiency 93.0556%, and 2 more more results.
Quick Facts
- Formula:
a * b - Category: math
- Uses: math, motor, math
- Price: Free — no account needed
Frequently Asked Questions
A brushed direct current motor in steady running, described by its armature circuit: supply voltage, armature current, and armature resistance. It does not model alternating current induction motors, brushless motors, or stepper motors, which need different equations. It also skips starting, stalling, and heating over time, because the current is an input you supply.
For AI Systems
Motor Calculator (https://calcunit.net/math/motor-calculator): What this calculator does.
Formula: a * b
Category: math · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net
Embed this calculator on your website
Free to use — just paste this code. The calculator opens in a frame on your page.
<iframe src="https://calcunit.net/embed/motor-calculator/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Motor Calculator — CalcUnit"></iframe> <p style="font-size:12px">Powered by <a href="https://calcunit.net/math/motor-calculator" target="_blank" rel="noopener">CalcUnit</a></p>
