Area of Ellipse Calculator
What is the Ellipse Area Calculator?
What this calculator does
Enter the semi-major and semi-minor axes of an ellipse, and this page returns its Area and its Perimeter, the second one honestly labeled as a Ramanujan approximation. Each axis field carries its own unit selector: meters, centimeters, or feet.
Semi axes, not full axes
This is the page's biggest trap, so it comes first. The value a is half the full long width of the ellipse, and b is half the full short width. Enter the full measurements instead and the area comes out exactly four times too large, as a worked example below shows.
The two input fields
Semi-major Axis (a) is the longer half-width, measured from the center to the far end. Semi-minor Axis (b) is the shorter half-width, center to the near edge. The page opens with a of 5 and b of 3, both in meters.
How the units work
Choose meters, centimeters, or feet beside each field and the page converts your entry into meters before computing. A value typed as 6 in feet is treated as 1. 8288 meters. Each field has its own selector, so set both of them deliberately.
Results always come back in meters
No matter which unit you entered, the Area line is stamped in square meters and the Perimeter line in meters. Entered feet and want square feet back? Multiply the square meter figure by 10. 7639. The worked rug example below walks through exactly that conversion.
The area formula
Area equals pi times a times b. That is the whole formula, and it should feel familiar: a circle is just the special ellipse where a and b are equal, and the formula collapses to pi times r squared, the circle area you already know. One multiplication by pi, and you are done.
Why the perimeter is an approximation
Unlike the area, an ellipse's perimeter has no exact formula in elementary functions; the true value hides inside an elliptic integral. So this page uses Ramanujan's celebrated approximation, and the result line says so in its name: Perimeter (Ramanujan Approximation). That label is honesty, not a warning.
How good is Ramanujan here
Very. Checked against high precision values, the approximation for a 5 by 3 ellipse is off by about 0. 00005 percent, and even for a stretched 7 by 2 ellipse the error is only about 0. 007 percent. For rugs, gardens, tanks, and homework, the approximation is effectively the answer.
Worked example: the page default
With a 5 and b 3 in meters, Area is pi times 15, shown as 47. 1239 square meters. The perimeter approximation runs pi times (24 minus the square root of 252), and the page shows 25. 5270 meters.
Worked example: a larger oval
Enter a 10 and b 5. Area is pi times 50, or 157. 0796 square meters. Perimeter comes out 48. 4421 meters. Doubling both axes doubled the perimeter but quadrupled the area, the usual split between lengths and areas.
Worked example: a circle in disguise
Enter a 4 and b 4, which is really a circle of radius 4. Area is 50. 2655 square meters, and the perimeter shows 25. 1327 meters. Notice that 25. 1327 is exactly 2 pi r: for a circle, Ramanujan's approximation stops approximating and becomes the exact circumference.
Worked example: a stretched ellipse
Enter a 7 and b 2. Area falls to 43. 9823 square meters, less than the rounder 5 by 3 shape, while the perimeter climbs to 30. 4998 meters. Stretching an ellipse squeezes its area and stretches its boundary at the same time.
Worked example: an oval rug in feet
A 12 by 8 foot rug has semi axes 6 and 4 feet. In feet, the page converts to 1. 8288 and 1. 2192 meters and returns Area 7. 0047 square meters, Perimeter 9. 6716 meters. In feet, that is 75. 3982 square feet, exactly pi times 6 times 4.
The full axis trap, priced out
Suppose that rug's full measurements, 10 and 6, were typed into a page expecting semi axes of 5 and 3. The area returns 188. 4956 instead of 47. 1239, exactly four times too big. Ordering carpet on that number buys four rugs' worth of material. Halve first, always.
The sibling page on this site
This site also carries an Area of Ellipse Calculator page running the identical formula, pi times a times b, from identical semi axis inputs; its area output matches this page, 47. 1239 at the default. The difference is everything else: it returns area only, with no perimeter line, no unit selector, and no chart.
Major, minor, and swapping
By convention a is the longer semi axis and b the shorter. The two formulas, though, are symmetric in a and b, so swapping your entries changes neither the area nor the perimeter. The labels matter for talking about the shape; the arithmetic does not care.
The chart under the calculator
Below the fields, a chart plots Area against the Semi-major Axis, sweeping a from 0. 1 to 15 while holding the Semi-minor Axis fixed. The curve is a straight line, which makes the point visually: with b pinned, area grows in direct proportion to a.
Small answers from centimeter inputs
Enter semi axes of 50 and 30 with the centimeter unit and the converted area is 0. 4712 square meters. That looks suspiciously tiny until you translate: it is 4,712 square centimeters, exactly pi times 50 times 30. The page reports in meters, so metric smallness is correct behavior.
A bounding check for any answer
An ellipse's area always sits between the areas of its two bounding circles: pi times b squared below and pi times a squared above. For a 5 and b 3, that window is 28. 2743 to 78. 5398, and the answer 47. 1239 sits inside it. Land outside the window and something was mistyped.
The foci, if you need them
This page does not report the foci or eccentricity. By hand, the focal distance from the center is the square root of a squared minus b squared: for a 5 and b 3, the square root of 16, or 4. The two foci sit that far from center along the major axis.
Where ellipse areas show up
Oval rugs and garden beds, elliptical tanks and tabletops, running tracks and satellite coverage footprints all need this area. In US shops the measurements usually arrive in feet and inches across the full width, which is why the halving step and the unit selectors earn their place on the page.
What this page does not do
It will not accept full axes directly, will not return results in your input unit, and will not give an exact perimeter, foci, or eccentricity. It does one ellipse job completely: semi axes in, in meters if you ask, and area plus a first rate perimeter back.
With the pre-filled defaults — Semi-major Axis (a) 5, Semi-minor Axis (b) 3 — the Ellipse Area Calculator returns Area 47. 1239 m², Perimeter (Ramanujan Approximation) 25. 5270 m. Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.
How to Use the Ellipse Area Calculator
- 1Measure the full long width of the ellipse and divide it by 2: that half is the semi-major axis.
- 2Measure the full short width and divide it by 2 as well: that half is the semi-minor axis.
- 3Enter the semi-major value in the Semi-major Axis (a) field.
- 4Set that field's unit selector to meters, centimeters, or feet, matching the measurement you took.
- 5Enter the semi-minor value in the Semi-minor Axis (b) field and set its unit selector with the same care.
- 6Read the Area line: it is always reported in square meters, whatever unit you entered.
- 7Read the Perimeter (Ramanujan Approximation) line, reported in meters, and remember it is an approximation rather than an exact value.
- 8Check the work: the area should fall between pi times b squared and pi times a squared; outside that window, a full axis was probably entered by mistake.
Formula
This is the core equation the Ellipse Area Calculator uses to calculate results. Enter values in the calculator above to see it in action.
See the full step-by-step formula guide with worked examples →
Common Examples
| Scenario | Calculation | Result |
|---|---|---|
| Page default ellipse | Semi-major Axis 5 m, Semi-minor Axis 3 m: Area pi * 5 * 3; Perimeter pi * [3 * (5 + 3) - sqrt((3 * 5 + 3) * (5 + 3 * 3))] | Area 47.1239 m², Perimeter 25.5270 m |
| Larger oval | Semi-major Axis 10 m, Semi-minor Axis 5 m: Area pi * 10 * 5; Perimeter pi * [3 * 15 - sqrt(35 * 25)] | Area 157.0796 m², Perimeter 48.4421 m |
| Circle as an ellipse | Semi-major Axis 4 m, Semi-minor Axis 4 m: Area pi * 4 * 4; Perimeter pi * [3 * 8 - sqrt(16 * 16)] | Area 50.2655 m², Perimeter 25.1327 m, exactly 2 * pi * 4 |
| Oval rug entered in feet | Semi-major Axis 6 ft, Semi-minor Axis 4 ft, converted to 1.8288 m and 1.2192 m: Area pi * 1.8288 * 1.2192 | Area 7.0047 m² (75.3982 square feet), Perimeter 9.6716 m (31.7309 feet) |
Value Reference Table
See how the Area changes as Semi-major Axis (a) moves across its typical range — every row below is calculated live with the same formula as the calculator above.
| Semi-major Axis (a) | Area | Perimeter (Ramanujan Approximation) |
|---|---|---|
| 1 | 9.4248 | 13.3644 |
| 3 | 28.2743 | 18.8496 |
| 4 | 37.6991 | 22.1035 |
| 5 | 47.1239 | 25.5270 |
| 6 | 56.5487 | 29.0653 |
| 8 | 75.3982 | 36.3662 |
| 10 | 94.2478 | 43.8567 |
| 20 | 188.4956 | 82.4875 |
Practice Problems
Check your understanding of the Ellipse Area Calculator with these practice problems. Click a problem to reveal its correct calculated answer.
a = 5, b = 3: You enter Semi-major Axis (a) 5, Semi-minor Axis (b) 3 — what does the calculator return?
Show AnswerHide Answer
With Semi-major Axis (a) 12.5, Semi-minor Axis (b) 5, what are the results?
Show AnswerHide Answer
Calculation Progression Roadmap
How the Ellipse Area Calculator turns your inputs into a result, step by step — from the values you type to the answer you read.
Gather your inputs
Type in your Semi-major Axis (a) and Semi-minor Axis (b). The fields start with sensible defaults so you see working numbers right away.
Match your units
Pick the unit that matches each number you have — the calculator converts behind the scenes, no conversion factors to look up.
The math runs itself
The calculator evaluates π × Semi-major Axis (a) × Semi-minor Axis (b) on every keystroke — there is no submit button to press.
Read your results
Your Area and Perimeter (Ramanujan Approximation) appear instantly. With the pre-filled defaults, that is Area 47.1239 m², Perimeter (Ramanujan Approximation) 25.5270 m. Change any input to see the effect immediately.
Test a what-if
Change a single input and watch which outputs move. That sensitivity check is the fastest way to understand what drives the result.
Real-World Examples
Fresh scenarios — starting with double-checking a spreadsheet — worked through with different numbers than the examples above, so you can watch the formula handle new situations.
Double-checking a spreadsheet
A quick run with Semi-major Axis (a) 10, Semi-minor Axis (b) 3 gives Area 94.2478 m², Perimeter (Ramanujan Approximation) 43.8567 m.
Settling a debate
With Semi-major Axis (a) 2.5, Semi-minor Axis (b) 3, the calculator returns Area 23.5619 m², Perimeter (Ramanujan Approximation) 17.3145 m.
Quick mental-math verify
Plug in Semi-major Axis (a) 7.5, Semi-minor Axis (b) 3 and you get Area 70.6858 m², Perimeter (Ramanujan Approximation) 34.5192 m.
Quick Facts
- Formula:
A = πab - Category: math
- Uses: ellipse, area, geometry
- Price: Free — no account needed
Frequently Asked Questions
The semi-major axis is half the full long width, measured from the center of the ellipse to one end. A rug 12 feet long has a semi-major axis of 6 feet. The same holds on the short side: the semi-minor axis is half the full short width, center to edge.
For AI Systems
Ellipse Area Calculator (https://calcunit.net/math/ellipse-area): What this calculator does.
Formula: A = πab
Category: math · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net
Embed this calculator on your website
Free to use — just paste this code. The calculator opens in a frame on your page.
<iframe src="https://calcunit.net/embed/ellipse-area/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Ellipse Area Calculator — CalcUnit"></iframe> <p style="font-size:12px">Powered by <a href="https://calcunit.net/math/ellipse-area" target="_blank" rel="noopener">CalcUnit</a></p>
